Amazing Plank Look Plywood Flooring Tutorial

19 Comments

Amazing Plank Look Plywood Flooring Tutorial
 
When recently redoing the room above our garage, we decided that we were DONE with the carpet. Our plans were to rip it up, plank the floor, and then paint it. We never expected the plywood planking that we made to look good enough to STAIN!
 
Yup, that’s plywood!



Here are the instructions:


Materials:

16 sheets of 15/32 pine plywood @ $16.49 per sheet
9 gigantic tubes of Liquid Nail @ $4.75 each
10 lbs of cut nails (ordered from Tremont Nail Company) @ $69.63 (includes s&h)
4 gallons of Varathane polyurethane @ $37.46 per gallon
2 quarts of stain @ $9.99 each

Square footage of the room: 533
Rough estimate of cost: $520

We started the project with sheets of plywood. We ripped them on the table saw into 6 inch strips that were all 8 feet long. Then, we Dustin carried all of this up to the house so it could sit and “acclimate” to the room. I don’t know if that helped, but that is something that is recommended when laying hardwood flooring. 


IMG_5313IMG_5319

It, surprisingly, only took us an hour and 45 minutes to cut the sheets into the planks.

With the materials purchased and gathered, Dustin cleaned up the room with the shop vac. He made sure all the subfloor panels were nailed down securely. Some required him to add some screws to make  sure they were tight. 

Then the fun started. We measured and figured… measured some more.. and some more…

Before we began, we made sure to figure out our pattern so that each row of flooring would alternate where the nails were. We also knew that we would need to cut shorter pieces for the end that were around 11 inches long. We wanted those “short” pieces to alternate back and forth with each row.


We started with the first board and squared it with the wall, leaving a 1/16 inch gap between the first board and the wall. We dry fitted it before applying a bead of Liquid Nail along the length of the board. We put the board in place and Dustin hammered in the nails on the marks. Later, he went though with a nail punch to make sure that the nails were at least flush with the flooring.

Between each board and each row, we left a 1/16 gap. The plan all along was to paint this flooring, so we wanted it to LOOK like planks instead of just a solid, painted panel floor. We worked our way back and forth, alternating which side we started on with each row. We didn’t worry about the 11 inch pieces we needed for each end until we were completely finished with the room.

IMG_5385 IMG_5376 

We wanted the nails to be in line, so we started this process by marking them as we went. (Later, I started marking them ahead of him because I wasn’t much help anywhere else). This also really sped up the process since he didn’t need to measure every 16 inches. After a while, Dustin made a jig to help with the measuring and marking for where the nails went. Then I just had to line it up with the previous board and mark rather than measure for every single nail.

IMG_5462

We ended up using 11 nails per board by alternating two nails then one then two, etc, as you can see in the above picture. We wanted it to have some order and thought they would look nicer lined up. We originally only nailed every 16 inches with two nails. When he took the first break, we realized that we needed to secure it a little more. The Liquid Nail was still wet and the board were moving up and down when we walked on them. That’s when he went back and added the single nail in line with each board.


Once it was all finished, we sanded the rough places and the spots where there was a little bit of blue and green paint from the lumber yard. As always, we had animal support throughout the whole process.  Up until this point here, we planned to paint the boards dark brown. We wanted a dark farmhouse plank floor look. We never imagined when we started that this would be a stainable project.


We hand stained the whole floor. There are tools that are made to make it easier and faster. We’ve never used them and wanted to make sure the stain went on evenly. And, we were dealing with plywood so we weren’t really sure what it was going to do. It went on perfectly… and in 4.5 hours.


We coated the floor with four coats of ploy. The first coat took about 8 hours to dry. We really didn’t want to have to sand between coats, so we made sure to recoat within 12 hours. He used a bristle applicator rather than a wool one. It seemed like he had better control over the thickness with it. We had to evacuate the house at night while it was drying. It was in the 30s outside, so opening the windows wasn’t’ really an option. He’s not wearing it in the above picture because he had just started, but he did wear a face mask the whole time he did the coats of poly.


Since we didn’t plan to stain this until the last minute, we weren’t concerned with the fact that you could see white spots on the subfloor beneath. We knew that those would get covered up when we painted the floor. Since we didn’t do that, something had to be done. At night, with the overhead lights on, those places GLARED white.

I went out and bought some Burnt Sienna Americana paint. One night, while Dustin hung the new ceiling fan, I scooted around on the floor with my Americana paint and a tiny paint brush and filled in the cracks. I wanted to wait until the floor was completely poly’ed and dry because if/hen I got it on the flooring, it wiped right off with a paper towel. It was the perfect color and was the perfect solution for our dilemma. 


Can you believe that this is the same room? Or, that this floor started its life as plywood?!

We are so happy with this flooring and our decisions! By doing this, we have saved well over $1500 that hardwood flooring would have cost. We like it so much, that we plan to do this in our kitchen soon. We plan to paint or whitewash it there though, hope you liked this plywood flooring tutorial!

We’ve moved all the furniture in and I’m just trying to figure out what to hang on the walls! I’ll definitely be putting the starburst mirror I made in here somewhere! The rest of the wall space is still up for grabs :)

About 

Cassity started Remodelaholic with her husband, Justin, to share their love for knocking out walls together. She is an interior designer, wife, and mother of two. She and Justin have remodeled three homes from top to bottom and are working on their fourth. Making a house a home is her favorite hobby.

    You can also find me on
  • facebook
  • googleplus
  • pinterest
  • twitter

Comments

  1. [email protected] says

    >Oh my gosh! that floor is awesome! I love how it all turned out, such a nice room. I love everything about this project.
    way to go Shannon!
    gail

  2. lauren says

    >that's amazing! I can't believe that started as a plywood board. I think the idea of putting it down in the kitchen and painting it is a great idea. how exciting to save $1500!

  3. Susan says

    >Awesome the room above our garage will be left unfinished. I will have to tell my hubby about this awesome project of yours.

  4. Lauralee @ The Eclectic Stitcher says

    >Absolutely stunning! We have 12" wide tongue&groove pine plank flooring that we installed ourselves (entire house) and your floor looks just as beautiful! Wish we had known about this 12 years ago…..

  5. Infarrantly Creative says

    >Oh my gosh Shannon that is amazing. I would have never thought of that in a billion years. That looks amazing. You are sure transforming your house.

  6. Cookie Momster says

    >Holy crap that is awesome!!! I am the cheapest person I know so this is right up my alley. I WILL be doing this on our next renovation. Incredible!

  7. Kat says

    >This is awesome!!! We are going to build our home in the future and this is an great alternative to those expensive wood floors!!! Thanks so much for sharing :)

  8. Shannon says

    >That is the best surprise ever. I'm showing this one to the husband. Great idea to use in his shop. Thanks so much for sharing.

  9. Eclectic Beader says

    >AMAZING is right. Who'd of thought that plywood could look so beautiful! Fantastic job and thanks for sharing the details.

  10. Becca says

    >Yay for you! I was just looking at hardwood floors online… I may just use this technique instead.. I want wide planks and those are pretty pricey. This would be a great alternative. You smarty pants you. :)

  11. Shannon says

    >Wow, thanks, everyone!
    :)

    We are SO IN LOVE with this room and the results. We spend all of our time up here now.

    There is ONE board that is creaky and it drives me insane. I think I'm going to have to add a nail while Dustin is gone sometime to fix it. (he's all about sticking with the pattern :) I'm all about one board not driving me batty!:))

    If anyone tries it, I'd love to see the results! This is the only way we were able to have 'hardwood flooring'. I'm so glad that some of you plan to try it out too!

    Shannon

    • Chris R says

      Shannon, thank you for the blog. Is has been very helpful and informative. I am considering doing the same plywood flooring in our apartment. What did you do to fill the gaps between the boards of plywood? Did the poly fill these gaps? Any advise or critique on this would be great.

      Chris R

  12. Annette H says

    WOW!! This looks fantastic!! I’d be interested to see/hear how these fab floors hold up to normal wear and tear. Job well done… I can’t wait to see what you guys do next! :) Thanks for sharing with us.

  13. Anna Hafen says

    I love this idea! We just bought a home and I plan on doing this in our front room, the plywood turned out amazing. In your materials list, you put that you got 15/32″ plywood. I saw some at the store that was 1/4″ and much cheaper. In your opinion, is that too thin for a floor?

    Thanks again for the great idea!

    Anna

    • says

      Anna, I would just really look at the quality of the pylwoods, if they are about the same then I don’t see that there would be a problem if the thickness is a little less. Good Luck!

  14. Chelsea says

    How would this work over concrete? Do I need to have plywood subfloor? I want to do this in my kitchen where the laminate is peeling up…

Leave a Reply

Your email address will not be published. Required fields are marked *